Downloads (1)

Pyrofil TR30S Data Sheet354 KB

Specification

Fabric Specification
Fibre SpecificsPyrofil TR30S, Polyester Yarn
ColourBlack/Red
Weave2 x 2 Twill
FormatWoven Fabric
Filament Count3k
Fibre TypeCarbon Fibre Hybrid
BrandToray
Ends6cm
Picks6cm
Fibre Orientation0, 90
Weight and Dimensions
Thickness0.3mm
Width1000mm
Consolidated Thickness0.3mm
Areal Weight210g/m²
Fibre Properties
UV ResistanceFully UV Stable
Compatible With
Compatible WithEpoxyYes
Compatible WithPolyesterYes
Compatible WithVinylesterYes
General Properties
Gross Weight0.21kg

Shipping Information

Restrictions

This product is not classed as dangerous goods for transport and can be shipped to all destinations without restriction.

Package Size

There are no package size restrictions or surcharges for this product.

Delivery Cost

To find the delivery cost of this item to your address, add it to your basket and then use the instant shipping calculator on the basket page.

210g Red 2x2 Twill 3k Carbon Fibre Cloth (1000mm)

Decorative carbon fibre hybrid fabric made by interweaving genuine 3k carbon fibre with eye-catching red polyester yarns to produce a black and red carbon fibre appearance. Although this fabric is fully structural in its performance, it is usually used only in a single, decorative surface layer, either as the first layer into a mould or applied onto the surface of existing parts.

1m wide, sold by the linear metre.


AVAILABILITY:More than 100 availablefor immediate shipping


PRICE
€23.25ex. VAT
(€23.25 /SQM)
More than 100 availablefor immediate shipping
QTY
LINEAR METRES
LINEAR METRES

Trade discounts

0-45-910-4950-99100+
€23.25€22.10€20.95€19.75€18.60
We won’t be beaten on price!

If you believe you’re buying an equivalent product cheaper elsewhere, contact us to discuss your requirements.

Stunning red carbon fibre fabric for a truly eye-catching part!

This very special fabric uses genuine 3k carbon fibre interwoven with a bright red polyester to create an amazing fabric that shimmers with bright red but is also distinctively carbon fibre with the jet black diagonal stripes of the 2/2 twill weave pattern.

Typical Uses

This special coloured fabric can be used in just the same way as standard carbon fibre and will bring a stunning and unique appearance to any project.

It is suitable for use in wet-lay, vacuum bagging and resin infusion manufacture as well as for use as a single surface layer where parts are being made to look like carbon fibre (skinning).

Please note that owing to the 50% coloured polyester yarn content of this fabric it does not have the same mechanical properties as 100% carbon fibre fabric, although it is still a high performance fabric.

How to Buy

This carbon fibre twill red roll is 1m (39") wide and the fabric is sold by the linear metre. The unit price shown is for 1 linear metre but volume discounts automatically apply for larger quantities of fabric.

Please purchase the number of linear metres you require. When purchasing multiple metres the fabric will be supplied in one continuous length on a roll.

Trade discounts

0-45-910-4950-99100+
€23.25€22.10€20.95€19.75€18.60
We won’t be beaten on price!

If you believe you’re buying an equivalent product cheaper elsewhere, contact us to discuss your requirements.

PRODUCT VIDEOS(1)

Stunning red carbon fibre fabric for a truly eye-catching part!

This very special fabric uses genuine 3k carbon fibre interwoven with a bright red polyester to create an amazing fabric that shimmers with bright red but is also distinctively carbon fibre with the jet black diagonal stripes of the 2/2 twill weave pattern.

Typical Uses

This special coloured fabric can be used in just the same way as standard carbon fibre and will bring a stunning and unique appearance to any project.

It is suitable for use in wet-lay, vacuum bagging and resin infusion manufacture as well as for use as a single surface layer where parts are being made to look like carbon fibre (skinning).

Please note that owing to the 50% coloured polyester yarn content of this fabric it does not have the same mechanical properties as 100% carbon fibre fabric, although it is still a high performance fabric.

How to Buy

This carbon fibre twill red roll is 1m (39") wide and the fabric is sold by the linear metre. The unit price shown is for 1 linear metre but volume discounts automatically apply for larger quantities of fabric.

Please purchase the number of linear metres you require. When purchasing multiple metres the fabric will be supplied in one continuous length on a roll.

Downloads (1)

Pyrofil TR30S Data Sheet354 KB

Specification

Fabric Specification
Fibre SpecificsPyrofil TR30S, Polyester Yarn
ColourBlack/Red
Weave2 x 2 Twill
FormatWoven Fabric
Filament Count3k
Fibre TypeCarbon Fibre Hybrid
BrandToray
Ends6cm
Picks6cm
Fibre Orientation0, 90
Weight and Dimensions
Thickness0.3mm
Width1000mm
Consolidated Thickness0.3mm
Areal Weight210g/m²
Fibre Properties
UV ResistanceFully UV Stable
Compatible With
Compatible WithEpoxyYes
Compatible WithPolyesterYes
Compatible WithVinylesterYes
General Properties
Gross Weight0.21kg
Can’t find the answer you’re looking for?Ask our technical team a question.

For wet-lay lamination you will use approximately the same weight of resin as the weight of the fabric. For example, with a 200gsm cloth, for 1 square metre you will have 200g of fabric and thus will need 200g of resin to wet it out, plus a small amount of wastage for the brush and mixing pot.

'3k' is the filament count or tow size. It simply means that each 'bunch' of carbon fibres that this cloth is woven from is made up of 3000 individual carbon filaments. Bigger counts (6k, 12k etc.) means chunkier 'bunches' of carbon so chunkier fabrics.

Thickness of any reinforcement is dependent on consoldation (how much it's 'squashed down'. For this reason we generally give out thickness figures for when the reiforcement is consoldated under vacuum (1bar); this seems like the most useful figure. For example, a 90gsm carbon, a single layer, compressed under vacuum, would be about 0.1mm thick. For a 200gsm carbon a single layer would be about 0.25mm thick. This is the number you see listed under 'thickness' in the specification table.

You can purchase a sample of our fabrics here.

Well, this depends entirely on what reinforcement you're laminating, speficically how thick and heavy it is. If you're laminating 5mm of carbon fibre you'll use a lot more resin that if you're laminating just 1mm of it. Fortunately though there a really quick rule to get a good estimate - simply add up the total weight of your reinforcement and you'll probably need the same weight in resin. This means that if you're laminating 5 layers of 200g carbon (so a total of 1000g of carbon) then you'll want about 1000g (i.e. 1kg) of Epoxy Resin. If it was 2 layers of 450g glass then you'd need about 900g per square metre.

The carbon fabric itself will survive many hundreds of degrees and is not the limiting factor for almost all applications. The limiting factor will be the heat distortion temperature of the resin system you plan to laminate this fabric with.



An engine rocker/cam cover may easily be exposed to hot oils at around 120°C as well as heat from the exhaust which would be dependent on the engine configuration and level of tune. As such we would recommend considering using a higher temperature resin system such as our Very High Temperature Epoxy Laminating Resin which, with an appropriate post-cure, can be used up to 180°C.



An alternative option would be to consider making the part with an out of autoclave pre-preg carbon fibre where typically the resin systems can achieve a HDT up to 120°C.

For very critical applications, such as aerospace, even dry carbon fabrics will be 'lifed' due to very gradual degradation of the sizing on the fibres, however in practice, for most applications, the degradation is minimal and most users would consider dry fabrics to not have a shelf life when stored appropriately.

All Carbon fibres are naturally charcoal black in colour.

Sorry, no. Our coloured hybrid carbon fabrics are currently available only as a raw carbon cloth - we do not have a pre-preg option.

If after trimming the panel and sanding the edges, you still have small pieces of the coloured cloth sticking out, you can trim them off by running a sharp stanley knife blade along the edge of the panel.

ASK YOUR OWN QUESTION

Note: Your name will be abbreviated and your email address will only be used to email you the answer directly

Note: Your name will be abbreviated and your email address will only be used to email you the answer directly

Customer Product Reviews for 210g Red 2x2 Twill 3k Carbon Fibre Cloth (1000mm)

No reviews

SUBMIT YOUR OWN PRODUCT REVIEW

We publish all reviews for verified purchases. Submit your own review and help other customers with their choices.

SUBMIT YOUR OWN PRODUCT REVIEW

We publish all reviews for verified purchases. Submit your own review and help other customers with their choices.

Shipping Information

Restrictions

This product is not classed as dangerous goods for transport and can be shipped to all destinations without restriction.

Package Size

There are no package size restrictions or surcharges for this product.

Delivery Cost

To find the delivery cost of this item to your address, add it to your basket and then use the instant shipping calculator on the basket page.

100% SECURE

    Secured by Digicert Payment processing by Adyen

PAYMENT METHODS

    Mastercard logo Visa logo Maestro logo Ideal logo Carte Bancaire logo Giropay logo Bancontact logo PayPal logo Bank transfer logo

Easy Composites EU B.V., registered in the Netherlands 73601195. All content copyright (C) Easy Composites Ltd, 2024. All rights reserved.