AT30 Epoxy Hardener

AT30 Epoxy Hardener for Easy Composites' EL2 Laminating Epoxy or IN2 Infusion Epoxy.

Available to buy separately, this is the hardener included with our EL2 and IN2 high performance epoxy resins.

AT30 Epoxy Hardener is available in FAST or SLOW and the two hardener speeds can also be mixed with each other to produce a hardener of precisely the required reactivity.

All our epoxies are sold with the relevant hardener included in the pack but if you require an additional hardener (because of spillage, incorrect use or if you require an alternative speed) then they can be purchased separately here.

FAST and SLOW hardeners can be blended to achieve pot-life and demould times anywhere between those stated in the specifications. However, you must still maintain the correct overall ratio of resin to hardener to ensure a proper cure.

How to Buy

The hardener is sold in sizes that match the hardeners from our resin packs, as follows:
115g (as included with our 500g resin pack)
230g (as included with our 1kg resin pack)
1.15kg (as included with our 5kg resin pack)
Please choose the speed and size from the drop-down menus at the top of the page.

Further Information

Key Processing Information

Ease of Use: Suitable for professional and hobby use (follow SDS advice).
Odour: AT30 is low odour with a slight ammonia smell on its own.
Safety Precautions: Wear gloves and goggles and work in a well ventilated area. Always read the SDS before use.
Ambient Conditions: Can be used from 15 to 30°C although pot-life and cure time will be affected significantly. Recommended working at an ambient of 20-25°C.
Degassing: Not necessary in most cases. Simply mix and use.
Mix Ratio: Mix 'Resin' and 'AT30 Hardener' 100:30 by weight. Use digital scales.
Mixing: Mix thoroughly by hand for at around 2 minutes.
Exotherm (Over-Heating): Resin will heat-up whilst it cures. Mix in small batches and use expediently. Mixed resin in a pot will quickly overheat (exotherm) and can smoke/ignite. Never leave mixed resin unattended.
Pigments and Fillers: A wide range of pigments and fillers can be added to change the properties and appearance of Resin.

Downloads (2)

This is a chemical product. Before storage or use you must download and read the accompanying safety and technical datasheets.

	Safety Datasheet (SDS) - EN	906 KB
	Safety Datasheet (SDS) - NL	913 KB

Specification

Cured Mechanical Properties

Max Service Temp	73	°C

Product Data

Viscosity	55	mPa.s
Pot Life (Typical)	14	mins
Colour	Clear
Chemistry / Material	Epoxy

Pot Life and Cure Times

Initial Cure Time	5	Hrs

General Properties

Gross Weight	0.15	kg

ASK YOUR OWN QUESTION

Shipping Information

Restrictions

This product is classed as dangerous goods for transport.

It can be shipped to all mainland EU countries, Ireland, Balearic Islands, Corsica, Sicily and Sardinia.

Unfortunately, for the time being we are unable to ship dangerous goods to Cyprus, Malta, the Canary Islands, Ceuta, Melilla, Jan Mayan and Svalbard.

For a full information regarding the shipment of dangerous goods, see our delivery information page.

Package Size

There are no package size restrictions or surcharges for this product.

Delivery Cost

To find the delivery cost of this item to your address, add it to your basket and then use the instant shipping calculator on the basket page.

RELATED PRODUCTS

IN2 Epoxy Infusion Resin
From €18.19 /KG

EL2 Epoxy Laminating Resin
From €17.65 /KG

CUSTOMERS ALSO PURCHASED

EL2 Epoxy Laminating Resin FAST 500g Kit
€15.35