Need any help or advice?+44 (0)1782 454499
Safety DataSheet (SDS) | 537 KB | |
Safety Datasheet (SDS) | 537 KB | |
Technical DataSheet (TDS) | 319 KB | |
Technical DataSheet (TDS) | 319 KB |
Working Time | 4 - 6 | mins |
---|---|---|
Handling Strength | 40 - 50 | mins |
Working Strength | 6 - 8 | Hours |
Full Cure Time | 1 - 1.5 | Days |
Shelf Life | 6 | Months |
---|---|---|
Hot Strength | 70 | °C |
Maximum Gap Fill | 0.5 | mm |
Mix Ratio | 1:1 | |
Colour | Off White | |
Chemistry / Material | Acrylic |
Shear Strength (Carbon Fibre) | 8 | N/mm² |
---|---|---|
Shear Strength (Stainless Steel) | 5 | N/mm² |
Suitable Uses | Composites | Yes |
---|---|---|
Suitable Uses | Metals | Yes |
Suitable Uses | Thermoset Plastics | Yes |
Suitable Uses | Most Thermoplastics | Yes |
Suitable Uses | Polyolefin Thermoplastics | Yes |
Gross Weight | 0.073 | kg |
---|---|---|
Brand | Permabond |
This product is not classed as dangerous goods for transport and can be shipped to all destinations without restriction.
There are no package size restrictions or surcharges for this product.
To find the delivery cost of this item to your address, add it to your basket and then use the instant shipping calculator on the basket page.
Acrylic adhesive specifically developed for the bonding of difficult-to-bond low surface energy plastics such as polyethylene, polypropylene, HDPE to each other and other substrates including metals and composite materials.
1:1 mix ratio. Off-white, 5-8min working time, 40-50min handling strength, full cure in 36hrs.
Available to buy in 50ml and 400ml cartridges (1:1 dispenser gun required). Includes one mixer nozzle.
AVAILABILITY:28 in stock available for immediate shipping
Trade discounts
0-9 | 10+ |
---|---|
€17.40 | €15.00 |
If you believe you’re buying an equivalent product cheaper elsewhere, contact us to discuss your requirements.
Permabond TA4610 is a two-part toughened MMA adhesive developed specifically for the bonding of difficult, low-surface energy polyolefin plastics such as polyethylene (PE), polypropylene (PP) and HDPE, with no primer or specialist surface treatment required.
As well as these difficult-to-bond polyolefin plastics, TA4610 also exhibits excellent bond strength to most other plastics, including thermoplastics like ABS, PVC, nylon and polycarbonate, as well as thermoset resins used in composite laminates such as epoxy, vinylester and polyester making it ideal for bonding PE, PP or HDPE to themselves or to just about any other substrate.
TA4610 is translucent pale yellow in colour. The adhesive contains no micro-beads and is intended for joints with smaller gaps (<0.5mm).
Main Characteristics
Working time | Handling Strength | Working Strength | Full Cure | Hot Strength | Mix Ratio | Gap Fill |
4-6mins | 40-50mins | 6-8hrs | 24-36hrs | 70°C | 1:1 | 0.5mm |
Pack Size and Dispensing
TA4610 is supplied in a 50ml or 400ml pack sizes which can be selected at the top of the page. Both pack sizes use 1:1 ratio cartridges and require a suitable cartridge dispenser gun.
The cartridges are intended to be used with static mixer nozzles which fully mix the two components as they pass through the nozzle. They are supplied with one nozzle but once used, adhesive cures in the nozzle and they need to be discarded. Additional nozzles are available to buy separately:
Shelf Life and Storage
TA4610 has a shelf life of 6 months at 25°C from date of manufacture. However, storing at a refrigerated temperature of around 5°C is highly recommended as it will prolong the shelf life and performance of the adhesive.
TA4610 is always stored refrigerated at 5°C in our warehouse.
Trade discounts
0-9 | 10+ |
---|---|
€17.40 | €15.00 |
If you believe you’re buying an equivalent product cheaper elsewhere, contact us to discuss your requirements.
Permabond TA4610 is a two-part toughened MMA adhesive developed specifically for the bonding of difficult, low-surface energy polyolefin plastics such as polyethylene (PE), polypropylene (PP) and HDPE, with no primer or specialist surface treatment required.
As well as these difficult-to-bond polyolefin plastics, TA4610 also exhibits excellent bond strength to most other plastics, including thermoplastics like ABS, PVC, nylon and polycarbonate, as well as thermoset resins used in composite laminates such as epoxy, vinylester and polyester making it ideal for bonding PE, PP or HDPE to themselves or to just about any other substrate.
TA4610 is translucent pale yellow in colour. The adhesive contains no micro-beads and is intended for joints with smaller gaps (<0.5mm).
Main Characteristics
Working time | Handling Strength | Working Strength | Full Cure | Hot Strength | Mix Ratio | Gap Fill |
4-6mins | 40-50mins | 6-8hrs | 24-36hrs | 70°C | 1:1 | 0.5mm |
Pack Size and Dispensing
TA4610 is supplied in a 50ml or 400ml pack sizes which can be selected at the top of the page. Both pack sizes use 1:1 ratio cartridges and require a suitable cartridge dispenser gun.
The cartridges are intended to be used with static mixer nozzles which fully mix the two components as they pass through the nozzle. They are supplied with one nozzle but once used, adhesive cures in the nozzle and they need to be discarded. Additional nozzles are available to buy separately:
Shelf Life and Storage
TA4610 has a shelf life of 6 months at 25°C from date of manufacture. However, storing at a refrigerated temperature of around 5°C is highly recommended as it will prolong the shelf life and performance of the adhesive.
TA4610 is always stored refrigerated at 5°C in our warehouse.
Working Time | 4 - 6 | mins |
---|---|---|
Handling Strength | 40 - 50 | mins |
Working Strength | 6 - 8 | Hours |
Full Cure Time | 1 - 1.5 | Days |
Shelf Life | 6 | Months |
---|---|---|
Hot Strength | 70 | °C |
Maximum Gap Fill | 0.5 | mm |
Mix Ratio | 1:1 | |
Colour | Off White | |
Chemistry / Material | Acrylic |
Shear Strength (Carbon Fibre) | 8 | N/mm² |
---|---|---|
Shear Strength (Stainless Steel) | 5 | N/mm² |
Suitable Uses | Composites | Yes |
---|---|---|
Suitable Uses | Metals | Yes |
Suitable Uses | Thermoset Plastics | Yes |
Suitable Uses | Most Thermoplastics | Yes |
Suitable Uses | Polyolefin Thermoplastics | Yes |
Gross Weight | 0.073 | kg |
---|---|---|
Brand | Permabond |
There is no practical minimum bond thickness for this adhesive although you do need to ensure that *some* adhesive is present, which is why glass spheres are sometimes used to prevent the adhesive from being scraped off completely. Essentially though, as long as an even thin film is applied the bond strength between the two materials will be good.
Yes, certainly. In fact the easiest way to do this is to simply leave the static mixer nozzle in place after you use the adhesive. The adhesive that's in the nozzle will have been mixed and so will cure but the glue at the start of the nozzle will be unmixed and not cured meaning the nozzle will twist off perfectly and the glue inside will have been protected from the atmosphere and so will be perfectly preserved ready for use.
A typical application of the adhesive is approximately a 0.5mm thick layer. At this thickness, one 50ml cartridge would cover an area 30cm by 30cm; a 400ml cartridge would cover an area approximately 90cm by 90cm.
For best results when gluing over a large surface area, use a spreader to help ensure the adhesive is laid down in an even layer.
There is no practical minimum bond thickness for this adhesive although you do need to ensure that *some* adhesive is present, which is why glass spheres are sometimes used to prevent the adhesive from being scraped off completely. Essentially though, as long as an even thin film is applied the bond strength between the two materials will be good.
Yes, certainly. In fact the easiest way to do this is to simply leave the static mixer nozzle in place after you use the adhesive. The adhesive that's in the nozzle will have been mixed and so will cure but the glue at the start of the nozzle will be unmixed and not cured meaning the nozzle will twist off perfectly and the glue inside will have been protected from the atmosphere and so will be perfectly preserved ready for use.
A typical application of the adhesive is approximately a 0.5mm thick layer. At this thickness, one 50ml cartridge would cover an area 30cm by 30cm; a 400ml cartridge would cover an area approximately 90cm by 90cm.
For best results when gluing over a large surface area, use a spreader to help ensure the adhesive is laid down in an even layer.
SUBMIT YOUR OWN PRODUCT REVIEW
We publish all reviews for verified purchases. Submit your own review and help other customers with their choices.SUBMIT YOUR OWN PRODUCT REVIEW
We publish all reviews for verified purchases. Submit your own review and help other customers with their choices.This product is not classed as dangerous goods for transport and can be shipped to all destinations without restriction.
There are no package size restrictions or surcharges for this product.
To find the delivery cost of this item to your address, add it to your basket and then use the instant shipping calculator on the basket page.
Easy Composites EU B.V., registered in the Netherlands 73601195. All content copyright (C) Easy Composites Ltd, 2024. All rights reserved.