Need any help or advice?
+44 (0)1782 454499
237 KBSpecification
Weight and Dimensions
| Width | 1250 | mm |
|---|---|---|
| Consolidated Thickness | 0.1 | mm |
| Areal Weight | 163 | g/m² |
Fibre Properties
| Out-life (at 20°C) | 30 | Days |
|---|
Product Data
| Colour | White | |
|---|---|---|
| Type | Adhesive Film | |
| Format | Flat Film | |
| Brand | XPREG |
Mechanical Properties
| Resin Matrix | Epoxy | |
|---|---|---|
| Min Cure Temp | 80 | °C |
| Max Cure Temp | 120 | °C |
| Max Service Temp | 120 | °C |
General Properties
| Gross Weight | 0.52 | kg |
|---|---|---|
| Brand | XPREG |
Shipping Information
Restrictions
This product is not classed as dangerous goods for transport and can be shipped to all destinations without restriction.
Prepreg Product - IMPORTANT!
Uncured prepreg materials are stored at -20°C and are shipped still frozen from our facility. This prepreg has an 'out-life' of at least 30 days at room temperature and so typical delivery times will still leave plenty of safe 'out-life' remaining.
During summer months or periods of hot weather, it is recommended to order prepregs at the start of the week (Monday or Tuesday) to avoid adding extra shipping days over the weekend.
Unless you plan to use the product immediately, it should be placed into frozen storage as soon as possible on receipt.
Package Size
The packaged size of this product exceeds 1.2m in length and so an additional handling surcharge (charged by the courier) will be included in the quoted shipping cost.
Delivery Cost
To find the delivery cost of this item to your address, add it to your basket and then use the instant shipping calculator on the basket page.
XA120 150g Prepreg Adhesive Film (1250mm)
- XPREG
- XA120-GPL-150(1250)-1
- No reviews
High performance 150gsm oven-cure prepreg adhesive film used for bonding honeycomb cores, such as aluminium and Nomex, and structural foams, such as Rohacell into composite laminate structures.
This adhesive film is 1.25m (1250mm) wide and available to buy in choice of pre-packed roll lengths.
PRODUCT VERSIONS
Roll Length
AVAILABILITY:4 in stock available for immediate shipping
34 more can built in 2-3 days
We won’t be beaten on price!
If you believe you’re buying an equivalent product cheaper elsewhere, contact us to discuss your requirements.
XPREG® XA120 is a structural epoxy adhesive film used to provide a high strength bond between composite laminate and core materials such as aluminium honeycomb, Nomex® or foam core (such as Rohacell®). This film adhesive can also be used to provide additional resin around bonding fasteners and inserts or underneath peel-ply when using peel-ply to provide a secondary bonding surface.
XA120's advanced, toughened epoxy formulation results in outstanding bond and peel-strength at the very forefront of adhesive film performance.
This prepreg resin film is suitable for autoclave, oven or heated platen press cure. XA120 cannot be cured at room temperature.
Advantages
- Industry leading bond and peel-strength
- Service temperature up to 120°C (subject to post-cure)
- Easy handling (4 week out-life)
- Minimal shrinkage, very low CTE
- Fully compatible with XPREG® XC110 and XC130 prepregs
Further Information
Cure Cycle
The recommended cure cycle for XA120 is 8hrs at 90°C (ramp rate 2°C/min) which will result in a Tg of 100°C. Where the maximum Tg is required, a post cure of 120°C for 1hr should be followed (ramp rate 0.3°C/min).
See datasheet for full details including alternative cure cycles from 80°C.
Compatibility with XPREG® Prepregs
XA120 is fully compatible with XPREG° XC110 (out-of-autoclave) and XC130 (autoclave) cure prepregs and can be co-cured with these prepreg systems or used in a '2-shot' process to provide secondary bonding onto laminates made using these systems (peel-ply finish or surface preparation would be required).
XPREG® XA120 is a structural epoxy adhesive film used to provide a high strength bond between composite laminate and core materials such as aluminium honeycomb, Nomex® or foam core (such as Rohacell®). This film adhesive can also be used to provide additional resin around bonding fasteners and inserts or underneath peel-ply when using peel-ply to provide a secondary bonding surface.
XA120's advanced, toughened epoxy formulation results in outstanding bond and peel-strength at the very forefront of adhesive film performance.
This prepreg resin film is suitable for autoclave, oven or heated platen press cure. XA120 cannot be cured at room temperature.
Advantages
- Industry leading bond and peel-strength
- Service temperature up to 120°C (subject to post-cure)
- Easy handling (4 week out-life)
- Minimal shrinkage, very low CTE
- Fully compatible with XPREG® XC110 and XC130 prepregs
Further Information
Cure Cycle
The recommended cure cycle for XA120 is 8hrs at 90°C (ramp rate 2°C/min) which will result in a Tg of 100°C. Where the maximum Tg is required, a post cure of 120°C for 1hr should be followed (ramp rate 0.3°C/min).
See datasheet for full details including alternative cure cycles from 80°C.
Compatibility with XPREG® Prepregs
XA120 is fully compatible with XPREG° XC110 (out-of-autoclave) and XC130 (autoclave) cure prepregs and can be co-cured with these prepreg systems or used in a '2-shot' process to provide secondary bonding onto laminates made using these systems (peel-ply finish or surface preparation would be required).
Specification
Weight and Dimensions
| Width | 1250 | mm |
|---|---|---|
| Consolidated Thickness | 0.1 | mm |
| Areal Weight | 163 | g/m² |
Fibre Properties
| Out-life (at 20°C) | 30 | Days |
|---|
Product Data
| Colour | White | |
|---|---|---|
| Type | Adhesive Film | |
| Format | Flat Film | |
| Brand | XPREG |
Mechanical Properties
| Resin Matrix | Epoxy | |
|---|---|---|
| Min Cure Temp | 80 | °C |
| Max Cure Temp | 120 | °C |
| Max Service Temp | 120 | °C |
General Properties
| Gross Weight | 0.52 | kg |
|---|---|---|
| Brand | XPREG |
Unfortunately we do not stock any pre-pregs with a flexible resin. The only flexible resin we supply is our EF80 Flexible Epoxy Resin which is suitable for wet lay and vacuum bagged processes.
No, XA120 Prepreg Adhesive film is designed to be used as an adhesive, particularly for bonding core materials to laminates as part of single or multi stage cure processes. It is not designed to be used as a 'resin film' or 'surface film' and in testing did not prove suitable for this application.
The film is nominally around 0.2mm thick in its uncured state. However, post curing, the thickness will reduce and vary depending on the use and curing process.
ASK YOUR OWN QUESTION
Customer Product Reviews for XA120 150g Prepreg Adhesive Film (1250mm)
SUBMIT YOUR OWN PRODUCT REVIEW
We publish all reviews for verified purchases. Submit your own review and help other customers with their choices.SUBMIT YOUR OWN PRODUCT REVIEW
We publish all reviews for verified purchases. Submit your own review and help other customers with their choices.Shipping Information
Restrictions
This product is not classed as dangerous goods for transport and can be shipped to all destinations without restriction.
Prepreg Product - IMPORTANT!
Uncured prepreg materials are stored at -20°C and are shipped still frozen from our facility. This prepreg has an 'out-life' of at least 30 days at room temperature and so typical delivery times will still leave plenty of safe 'out-life' remaining.
During summer months or periods of hot weather, it is recommended to order prepregs at the start of the week (Monday or Tuesday) to avoid adding extra shipping days over the weekend.
Unless you plan to use the product immediately, it should be placed into frozen storage as soon as possible on receipt.
Package Size
The packaged size of this product exceeds 1.2m in length and so an additional handling surcharge (charged by the courier) will be included in the quoted shipping cost.
Delivery Cost
To find the delivery cost of this item to your address, add it to your basket and then use the instant shipping calculator on the basket page.
CUSTOMERS ALSO PURCHASED
CUSTOMERS ALSO PURCHASED
100% SECURE
PAYMENT METHODS
Easy Composites EU B.V., registered in the Netherlands 73601195. All content copyright (C) Easy Composites Ltd, 2024. All rights reserved.